Hypertherm, HyPerformance, HyDefinition, LongLife and CommandTHC are trademarks of .. HPRXD Manual Gas – Revision 2. guarantees the Hypertherm quality you can count on. The HPRXD delivers superior bar ( psi) Manual gas console. 8 bar ( psi). ArcGlide, EDGE Pro, Hypertherm, HPR and Sensor THC are trademarks of Hypertherm, Inc. and may be When you see a safety symbol in this manual or on your machine HPRXD, HPRXD with a built-in.
|Published (Last):||17 July 2006|
|PDF File Size:||4.50 Mb|
|ePub File Size:||16.90 Mb|
|Price:||Free* [*Free Regsitration Required]|
Input power Be sure to connect the power cord ground wire to the ground in the disconnect box.
Keep a fire extinguisher nearby. Connectors on these cables should have a metal housing and the shield, not the drain, should be manial to the metal housing of the connectors at each end of the cable. The hyperthrrm console may be mounted horizontally or vertically.
Accordingly, although the plasma arc has not been identified as a source of toxic fumes, the material being cut can be a source of toxic fumes or es that deplete oxygen.
Is it the operators console on your CNC machine Tighten the securing screws. Use a high-quality, -stage, regulator to maintain consistent supply pressure, if using liquid cryogenic or bulk storage. Wear correct and appropriate protective equipment to protect head, eyes, ears, hands, and body.
Do not stand, sit hpyertherm lie on or touch any wet surface when using the plasma system. Services d inspection technique Date: No corte cerca de sustancias inflamables. Material composition, surface finish, and composition of coatings.
Do not touch live parts. En premier lieu, vider et nettoyer correctement le contenant.
Ground all system components to earth. Originally Posted by pontiacg5.
HyPerformance Plasma. HPRXD Manual gas. Instruction manual Revision 2 – PDF
El propietario del equipo y las instalaciones debe analizar la calidad del aire del lugar donde se usa el equipo, para asegurarse de que cumpla con todas las normas y reglamentaciones locales y nacionales.
The hoses must not be twisted. Always use purified water in the coolant mixture in order to prevent damage to the pump and corrosion in the torch coolant system. The cable used must have a braided shield, not a foil shield. Porter des gants isolants. Torch The virtually dross-free cutting capacity of the torch is 38 mm. Cuffless trousers to prevent entry of sparks and slag. Connect the power leads to the terminals of TB as shown below.
Refer to the Material Safety Data Sheets appendix for data on safety, handling and storage of propylene glycol and benzotriazole. Coloque carteles o anuncios.
It is important that the operator and maintenance technician understand the intent of these warning symbols as described. It contains hypertyerm circuitry to ignite a torch, a heat exchanger and pump to cool the torch.
Any damage or injury caused by the use of other than genuine Hypertherm parts may not be covered by the Hypertherm warranty, and will constitute misuse of the Hypertherm Product. No permita que nadie la opere sin las instrucciones correspondientes. Screening of the entire plasma cutting installation may be considered for special applications.
Hypertherm HPRXD Manual Gas Rev.3 manuals
It also requires that the slats, on which the workpiece rests, make good contact with the table and the workpiece. Never allow electrical contact between the plasma arc and a cylinder. If there is evidence of damage, refer to Claims. Store PC boards in anti-static containers. All access and service doors hyperttherm covers should be closed and properly fastened when the cutting equipment is in operation.
Use a high-quality, 2-stage pressure regulator located within 3 m 0 ft of the console. Computer and other control equipment. Replace a damaged power cord immediately. Vous venez d acheter un kit de connexion Urban Factory pour Microsoft Mmanual, et nous vous.