HCNW3120 DATASHEET PDF

HCNW datasheet, HCNW pdf, HCNW data sheet, datasheet, data sheet, pdf, Agilent (Hewlett-Packard), Amp Output Current IGBT Gate Drive. Broadcom HCNW available from 7 distributors. Explore Optoelectronics on Octopart: the fastest source for datasheets, pricing, specs and availability. HCNW datasheet, HCNW circuit, HCNW data sheet: HP – Amp Output Current IGBT Gate Drive Optocoupler,alldatasheet, datasheet.

Author: Vukasa Tygokasa
Country: Sao Tome and Principe
Language: English (Spanish)
Genre: Automotive
Published (Last): 19 October 2017
Pages: 457
PDF File Size: 7.47 Mb
ePub File Size: 7.90 Mb
ISBN: 429-5-85024-670-6
Downloads: 94706
Price: Free* [*Free Regsitration Required]
Uploader: Tuzilkree

Any overlap in Q1 and Q2 conduction will result in large currents flowing through the power devices between the high and low voltage motor rails. Creepage and clearance distances will also change datasheeet on factors such as pollution degree and insulation level. The LED is optically coupled to an integrated circuit with a power datashheet stage.

The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. Contact your Avago Technologies sales representative or authorized distributor for information.

HCNW Datasheet(PDF) – Agilent(Hewlett-Packard)

Maintenance of the safety data shall be ensured by means of protective circuits. Lab datasheeet in this note. To minimize dead time in a given design, the turn on of LED2 should be delayed relative to the turn off of LED1 so that under worst-case conditions, transistor Q1 has just turned off when transistor Q2 turns on, as shown in Figure Figure 33 is an alternative drive circuit which, like the recommended application circuit Figure 25does achieve ultra high CMR performance by shunting the LED in daasheet off state.

  EL MODELO MUNDELL FLEMING PDF

However, this shield does not eliminate the capacitive coupling between the LED and optocoupler pins 5—8 as shown in Figure All other brand and product names may be trademarks of their respective companies.

To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Contact an Avago Technologies sales representative datashewt authorized distributor. Minimum External Tracking L Creepage 7.

Delaying the LED signal by the maximum propagation delay difference ensures that the minimum dead time is zero, but it does not tell a designer what the maximum dead time will be. This capacitive coupling causes perturbations in the LED current during common mode transients and becomes the major source of CMR failures for a shielded optocoupler.

Option data sheets are available. This is achieved by overdriving the LED current beyond the input threshold so that it is not pulled below the threshold during a transient.

HCNW3120 Datasheet

The high operating voltage range of the output stage provides the drive voltages required by gate controlled devices. Documents Flashcards Grammar checker.

Device considered a two-terminal device: Techniques to keep the LED in the proper state are discussed in the next two sections. For the continuous voltage rating refer to your equipment level safety specification or Broadcom Ltd. When negative gate drive is not used VEE in the previous equation is equal to zero volts. For creepage, the shortest distance path along the surface of a printed circuit board between the solder fillets of the input and output leads must datasheeet considered.

  ELECTRODYNAMIQUE QUANTIQUE EXERCICES PDF

Dead time is the time period during which both the high and low side power transistors Q1 and Q2 in Figure 25 are off.

HCPL-3120/J312, HCNW3120

However, once mounted on a printed circuit board, minimum creepage and clearance requirements must be met as specified for individual equipment standards.

Note that the propagation delays used to calculate PDD and dead time are taken at equal temperatures and test conditions since the optocouplers under consideration are datasheer mounted in close proximity hxnw3120 each other and are switching identical IGBTs. Temperature Figure 3 VOH vs. Pins 1 and 4 need to be connected to LED common.

See Applications section for additional details on limiting IOH peak.

HCNW Datasheet(PDF) – AVAGO TECHNOLOGIES LIMITED

AVEN — March 21, Data subject to change. This results in lower peak currents more margin than predicted by this analysis. These dimensions are needed as a starting point for the equipment designer when determining the circuit insulation requirements. In this test, VOH is measured with a dc load current. There are recommended techniques such as grooves and ribs which may be used on a printed circuit board to achieve desired creepage and clearances.

The thermal resistance values given in this model can be used to calculate the temperatures at each node for a given operating condition.