ASTM A265 PDF

ASTM A ASME SA “Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel. Plate”. “STANDARD SPECIFICATION FOR NICKEL AND. Buy ASTM A SPECIFICATION FOR NICKEL AND NICKEL-BASE ALLOY-CLAD STEEL PLATE from SAI Global. Designation: A − 12Standard Specification for Nickel and Nickel-Base Alloy- Clad Steel Plate1 This standard is issued unde.

Author: Tygomi Dasho
Country: Yemen
Language: English (Spanish)
Genre: Technology
Published (Last): 12 May 2013
Pages: 100
PDF File Size: 8.92 Mb
ePub File Size: 13.55 Mb
ISBN: 857-4-37751-996-3
Downloads: 11268
Price: Free* [*Free Regsitration Required]
Uploader: Kagagore

General Requirements for Delivery The material is generally intended for pressure vessel use but may be used in other structural applications where corrosion resistance of the alloy is of prime importance.

When none has been speci? All other tensile test requirements of the speci? It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. This abstract is a brief summary of wstm referenced standard.

ASTM A265 Clad Plate

Method of test and acceptance standard shall be as agreed upon between the purchaser and the manufacturer. Greater separation shall be cause for rejection. The nickel or nickel-base alloy cladding metal shall conform to prescribed chemical composition. If the requirements of this speci? Satm Variations Metric Equivalents in.

The tensile properties thus determined shall meet the base steel requirements. Chemical analysis may be accomplished by wet chemical or instrumental procedures. Areas within 1 in.

ASTM A265 GR 1 titanium alloy strip sheet plate

If wet chemical procedures are used, millings may be taken only when the composite plate thickness is sufficient to permit obtaining millings without danger of contamination from the adjacent layer. The minimum cladding thickness for shear testing shall be 0. Specify whether applicable to the cladding alloy, backing steel, or both see Section The sides of the bend test specimen used for bond strength determination may have the corners rounded to a radius not over 1?

  EXERCICIOS DE TERMOMETRIA EM PDF

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

The base metal shall conform to the chemical requirements of the speci?

NOTE 3—The dimension t is the thickness of the test specimen as provided for in the applicable material speci? The surface condition of the repaired area shall be restored to a condition similar to the rest of the cladding. Each specimen shall be in the? This specification covers the standard for plate of a carbon steel or a2665 steel base to which is integrally and continuously bonded on one or both sides a layer of nickel or nickel-base alloy.

Asttm requirements may include, but are not limited to the following: The material is generally intended for pressure vessel use but may be used in other structural applications where corrosion resistance of the alloy is of prime importance. Workmanship Finish, and Appearance ASTM International takes no position respecting the aastm of any patent rights asserted in connection with any item mentioned in this standard.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

Approved May 1, This standard has been approved for use by agencies of the Department of Defense. The base metal shall be carbon steel or low-alloy steel conforming to the specifications for steels for either pressure vessels or for general structural applications.

  JURNAL ISSN ALELOPATI PDF

Historical Version s – view previous versions of standard Translated Version s: Gage Length cladding and the base steel shall be machined so as to maintain the same ratio of clad metal to base steel as is maintained in the plate, except that the thickness of the clad material need not be reduced below 1?

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

A list of standardized supplementary requirements for use at the option of the purchaser are included in Speci? Product and chemical analyses shall be performed on the cladding alloy and be accomplished by wet chemical or instrumental procedures.

ASTM A GR 1 titanium alloy strip sheet plate

Materials and Manufacture 5. A number in parentheses indicates the year of last reapproval.

Number of Tests and Retests 8. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Originally approved in The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

NOTE 2—Punch marks for measuring elongation after fracture shall be made on the?