ASTM A/AM: Standard Specification for Stainless Steel Spring Wire. Copper. % max. Phosphorus% max Nickel. – %. Silicon. % max Nitrogen% max. Tensile Strength Table (ASTM-A) *KSI. Over. Stainless Steel Wire, AISI / ASTM A , Cr % Ni %, 28 () , 10 (), , C, Request a Quote. AISI ASTM A , Cr
|Published (Last):||28 September 2012|
|PDF File Size:||14.35 Mb|
|ePub File Size:||12.40 Mb|
|Price:||Free* [*Free Regsitration Required]|
These specimens shall be tested in a bending machine conforming substantially to Fig. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Following fabrication Type and Grade XM shall be age or precipitation hardened to produce their maximum strength properties.
The nominal as-drawn tensile strengths are provided as a guide for the spring manufacturer. Stainless steel spring wires are economic, general purpose wires that provide high tensile strength coupled with good to superior corrosion resistance and magnetic properties.
Our staff has the experience to assist you in selecting the best stainless steel alloy for your application and to manufacture a custom spring steel wire that meets or exceeds aa313 expectations. A piece not more than 10 in. Within the text and tables, the SI units are shown in brackets.
Within the text atm tables, the SI units are shown in brackets. These specimens shall be tested in a bending machine conforming substantially to Fig. The nominal as-drawn tensile strengths are provided as a guide for the spring manufacturer. It is used for springs in corrosive environments that do not require high impact or load strength.
ASTM A AM – 98 Stainless Steel Spring Wire_百度文库
ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Click here to contact us today or call us at The wire shall lie? It maintains its strength at temperatures up to degrees F. After this treatment, the specimen coil shall show uniform pitch with no splits or fractures.
The wire shall w313
ASTM A / AM – 18 Standard Specification for Stainless Steel Spring Wire
After this treatment, the specimen coil shall show uniform pitch with no splits or fractures. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Combining values from the two systems may result in nonconformance with the speci? Work Item s – proposed revisions of this standard. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.
Failure to comply with the general requirements of Speci? B Maximum unless range is shown. Originally approved in Lubricating coatings, which are insoluble in acid etch solution, shall atsm removed before etching. Type Class 2 shall be stress relieved following fabrication and meet the requirements shown in Table 4. NOTE 1—A asrm ordering description is as axtm Following fabrication Type and Grade XM shall be age or precipitation hardened to produce their maximum strength properties.
Stainless Steel 302
A superscript epsilon e indicates an editorial a3313 since the last revision or reapproval. Your comments are invited either for revision z313 this standard or for additional standards and should be addressed to ASTM Headquarters. BS steel wir This abstract is a brief summary of the referenced standard.
Tensile strength requirements ast, hardened wires and stress-relieved materials shall be given. Call today to see how we can solve your stainless steel spring manufacturing challenge. For over 85 years, General Wire Spring has offered compression springs, extension springs, torsion spring, and wire forms manufactured using stainless steel spring wire.
Go to Navigation Go to Content. A piece not more than 10 in. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. You can be assured that your springs will be delivered to you fast and ready for your production line.
Type Class 2 shall be stress relieved following fabrication and meet the requirements shown in Table 4. B Maximum unless range is shown.
This standard is sstm to revision at any time by the responsible technical committee and must be reviewed every? Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. It exhibits superior fatigue properties, elasticity, strength-to-weight ration, high yield strength, ductility, and good corrosion resistance, at temperatures up to degrees F.
Such requirements may include, but are not limited to the following: J Numbering Metals and Alloys4 3. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Mechanical tests such as wrap test, uniformity coil testand bend test hall be performed on the steel material.
General Requirements for Delivery 4.